SYXC-Y89-B淹没式脉冲阀

浏览量：

1000

SYXC-Y89-B Submerged pulse valve

所属分类：

产品分类

联系我们

产品描述
Product Details

　　SYXC-Y89-B型淹没式脉冲阀用于脉冲袋式除尘器的喷吹清灰。此型脉冲阀采用淹没于气包中的结构，与其他结构形式比较，减少了流道阻力，降低了喷吹气源压力，因而能适用于压力低的场合，且可降低能源消耗和延长膜片寿命。

　　产品结构

　　壳　体：阀门的外壳和封盖是用铝合金压模铸造而成，外观好、强度高，能确保无漏气现象。阀门的压力流道设计合理，阀的开、闭面基本位于气包内，真正实现了“淹没式”，空气可由气包直接进入喷吹管，这就真正达到了低气压、大喷吹量的要求。
　　电磁阀：电磁阀以遥控方法操作脉冲阀。带有插入式线圈和DIN电线插座。方便内部或外部安装，放水防尘保护，符合JB/T5916-91标准。
　　阀膜片：膜片位移大，在0.08-0.1秒的短时间内也能确保阀的开度。应用于寒冷气候环境时可选择进口材料研制的合成橡胶膜片。工作温度可在-40℃到55℃之间，并能确保最长的工作寿命。

　　技术参数

工作压力	0.2Mpa~0.6Mpa
气源介质	洁净空气
防护等级	IP65
电压	DC24V、AC220V、AC110V
温度等级	1	2
	-15℃~80℃	-35℃~230℃
环境温度	-15℃~50℃
环境湿度	相对湿度不大于85%

　　电磁脉冲阀外形尺寸、安装尺寸

　　气包开孔尺寸见下表

(mm)

型号	喷吹口径	主孔		定位或固定孔
型号	喷吹口径	分气箱 A	喷吹孔 B	中心圆 C	φ D
SYXC-Y89-B	3"	φ164	φ94	φ227	6×M10

　　附注

　　1.一般供货，电压均为DC24V，如需AC220V，AC110V均请在订货时说明；
　　2.使用Y型脉冲阀时，建议把阀水平地安装气包顶面；
　　3.装阀时为避免把阀出口内的“O”形密封环顶错位，务请在此环上预先涂润滑脂。
　　4.技术参数中温度等级“2”参数，属耐高、低温脉冲阀，订货需说明。

The SYXC-Y89-B submersible pulse valve is used for the jet cleaning of pulse bag filters. This type of pulse valve adopts a structure submerged in the air tank. Compared with other structural forms, it reduces the flow channel resistance and lowers the pressure of the injection air source. Therefore, it can be applied in low-pressure situations, and can also reduce energy consumption and extend the diaphragm life.

　　Product structure

The shell: The outer shell and cover of the valve are made of aluminum alloy by die-casting, which has a good appearance and high strength, and can ensure no air leakage. The pressure flow channel design of the valve is reasonable. The opening and closing surfaces of the valve are basically located inside the air tank, truly achieving "submerged". Air can directly enter the blowing pipe from the air tank, which truly meets the requirements of low pressure and large blowing volume.
Solenoid valve: The solenoid valve operates the pulse valve by remote control. With plug-in coil and DIN wire socket. It is convenient for internal or external installation, with water and dust protection, and complies with the JB/T5916-91 standard.
Valve diaphragm: The diaphragm has a large displacement and can ensure the valve opening within a short period of 0.08 to 0.1 seconds. When applied in cold climate environments, synthetic rubber diaphragms developed from imported materials can be selected. The working temperature can range from -40℃ to 55℃, and it can ensure the longest working life.

　　Technical parameters

Work pressure	0.2Mpa~0.6Mpa
Gas source medium	Clean air
Protection grade	IP65
Volta	DC24V、AC220V、AC110V
Temperature grade	1	2
	-15℃~80℃	-35℃~230℃
Ambient temperature	-15℃~50℃
Environmental humidity	The relative humidity shall not exceed 85%

The external dimensions and installation dimensions of the electromagnetic pulse valve

　　The opening dimensions of the air tank are shown in the table below

(mm)

Model	Injection diameter	Main hole		Positioning or fixing holes
Model	Injection diameter	Gas distribution box A	Blowing hole B	Central circle C	φ D
SYXC-Y89-B	3"	φ164	φ94	φ227	6×M10

　　Notes

　　1.For general supply, the voltage is all DC24V. If you need AC220V or AC110V, please specify when placing an order.
　　2.When using a Y-type pulse valve, it is recommended to install the valve horizontally on the top surface of the air tank.
　　3.When installing the valve, to prevent the "O" ring inside the valve outlet from being misaligned, please apply grease to this ring in advance.
　　4.The temperature grade "2" parameter in the technical parameters is a high and low temperature resistant pulse valve. Please specify when placing an order.

关键词 :
- SYXC-Y89-B
- 淹没式
- 脉冲阀